![BBC 454 SCAT ROTATING ASSEMBLY WISECO FLAT TOP FORGED PISTONS 454+FT-4.310-1pc](https://old.skipwhiteperformance.com/media/cache/01/9b/019bfffc3ae95c04531398f1c077ca14.jpg)
BBC 454 SCAT ROTATING ASSEMBLY WISECO FLAT TOP FORGED PISTONS 454+FT-4.310-1pc
Available
$1,650.00
Product Information
UPC | 353414764896 |
---|---|
Product Type | Shipped Product |
Shipping Cost | $159.50 |
Number of reviews | 0 |
FULLY BALANCED BBC 454 CID +.060 OVER
ROTATING ASSEMBLY WITH WISECO RACING FORGED DOME PISTONS, 4.310 BORE. .060 OVER +3cc FLAT TOP, Scat or Eagle Crankshaft & SCAT H-BEAM 6.135 RODS
FITS 1PC REAR MAIN SEAL BLOCKS.
BALANCED IN HOUSE.
*** IMPORTANT NOTE ***
You may add items into your shopping cart but in order to check out you will have to call us. Our check out feature on our website is being upgraded at this time. We can take your order over the phone and answer any technical questions you may have. We accept all major credit cards, cash, check, and money orders. Just give us a call at 423-722-5152 and we can process your order promptly. In the event you attempt to reach us outside of our operating hours, please leave us a detailed message and we will return your call at our earliest opportunity.
See the detailed info below for info on what is included in this assembly.
GENERAL SPECS.
- Crankshaft: Genuine Scat or Eagle, depending on availability
- Crankshaft Stroke: 4.00"
- Crankshaft Material : Cast Nodular
- Journal Diameter: STD Mains
- Rear Main Seal: 1pc RMS
- Connecting Rods: Genuine Scat
- Connecting Rod Type: Genuine Scat H-Beam with ARP Cap Screws.
- Connecting Rod Size: 6.135"
- Wrist Pin: Full Floating
- Connecting Rod Material: Forged 4340 Steel
- Pistons: Wiseco Fully Forged High Performance
- Piston Size: 4.310"
- Dome Volume: -3cc Flat Top
- Piston Material: Forged 2618 Aircraft Alloy
- Piston Rings: Hastings High Performance
- Ring Size: 5/64 5/64 3/16
- Ring Fit: Drop-In. Ready to install.
- Ring Tension: Standard
- Ring Material: Ductile Iron/Cast/Stainless/Moly
- Main Bearings: King SI series
- Rod Bearings: King SI series
- Balance: Ext. In House on CWT balancer.
- Damper: Pro-Race brand Pro-Sport Series SFI
- Flexplate: 168 tooth heavy duty; 153 tooth is available. Manual Trans. flywheels also available.
- Block requirements: standard deck height 9.800
Compression Ratio Chart.
The calculations below assume your pistons are at zero deck. Let's say your compression calculates out to be 10.50 for example based on having the pistons at zero deck (flush with the deck), but your pistons were going to be .005 in the hole, then the comp. ratio would only drop to 10.40, and if left .010 in the hole, then it would drop to approx. 10.30 We do recommend having your block decked to allow the piston to set anywhere from flush (zero) to .005 in the hole for optimal performance.
We have highlighted in red the compression ratio for the bore size and piston volume of this assembly using several popular combustion chamber sizes.
Part Number |
Cylinder Head Volume |
|||
106.0cc |
117.0cc |
119.0cc |
121.0cc |
|
BBC 454 |
Static Compression Ratio |
|||
4.280 Bore |
8.88 |
8.22 |
8.11 |
8.00 |
4.310 Bore |
8.99 |
8.32 |
8.21 |
8.10 |
AVAILABLE IN 1 PC AND 2 PC RMS, VARIOUS BORE SIZES AND WE OFFER FLAT TOP AND VARIOUS SIZED DOME PISTONS.
Listed below is a complete breakdown of all the parts that are included in this assembly.
Our custom made Wiseco pistons are rated very high in the street/strip performance industry. Wiseco normally offer several grades of pistons, starting with the lower grade Pro-Tru Street version made with 4032 forged alloy. The next level up would be the professional series that are much more expensive and made from 2618 aircraft alloy and have fully machined crowns rather than the as cast crowns that are on the Pro-Tru series. Our Wiseco pistons are custom made for us, and have both of these premium features, 2618 Alloy, and fully machined crowns. All premium grade forged pistons on the market have these two unique features and usually cost around $800-$1100 per set.
We have built approximately 8000 engines using the Wiseco pistons over the past 10 years. The engines have been for street rod and strip use. We have seen no problems, nor have there been any complaints. They are an excellent product in every respect.
Important note
Many customers have asked us what size they should bore their block at to allow for a proper piston to wall clearance. The required clearance is built into the piston already. For example if these pistons show a given size such as 4.030 then that is exactly what you will bore the block to. The actual size of the pistons when measured at the skirt, 1/2 inch above the tang will show to be approx. 4.026. The needed clearance is built in. Should you be using these pistons in a marine app. where the boat receives it's water from the lake, then an additional 1.5-2.0 thous. would be added to your final bore size, and some forced induction apps may also require a slight increase in bore size.
These pistons are totally suitable for use with mid level nitrous or blower setups. Extreme level builds that are making hp numbers in the 1000 hp range will require a set of custom made extreme duty pistons.
Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.
Our custom made pistons have a compression height that is .010 taller on bbc pistons, and .015 taller on sbc pistons, as compared to most all of the catalog pistons on the market. We find this to be a very valuable feature.
Since our pistons sit at a taller than normal compression height, you will only have to remove approx. .005-.010 off the deck surface of a virgin block to achieve a zero deck (flush with the deck surface). This maintains the deck's thickness, making it much stronger than a block that has been cut down .025. The engine will also run a bit cooler with a thicker deck. It's well known that the deck dissipates much of the built up heat an engine generates. This also allows for future deck re-surfacing without compromising the integrity of the block. Most all catalog pistons on the market require cutting the deck surface around .025 to achieve a zero deck. A zero deck is very important as it keeps the quench/squish zone at or near an optimal .040 distance. Be sure and let your machine shop know what the compression height is on these pistons before they machine your deck surface.
We do our own balancing with our brand new, 2013 model CWT 5500 Series Balancer, which replaced our 2011 Hines Legend balancer. The CWT 5500 is the absolute ultimate for precision balancing. When we balance the assembly, it will be to very high specs., usually plus or minus 1-2 grams. We include a balance sheet with your setup.
Scat cast nodular crankshafts are manufactured from an exclusive Space Age cast steel material that was designed for high strength and fatigue resistance. The Scat cranks are 25% stronger than stock OEM cast cranks and are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for your street rod, dirt track/circle track racing, and drag strip racing performance engine.
We do all balancing in house.
Our Scat crankshafts are brand new, factory sealed, not a blem. Beware of sellers offering no name cranks. We sell plenty of no name products but we have seen too many issues with the no name cranks on the market.
Our machinist who does the balancing made special note of how much harder these cranks were compared to any of the other cast nodular cranks on the market.
We recommend that you check the thrust clearance on the crank before assembling the engine. This is recommended on any crankshaft, regardless of brand or cost. Also check your main and rod journal size, as it's also not uncommon to find some cranks on the small or large side by as little as half a thousandths or less.
On occasion, our engine shop requires a half shell to correct this for perfect clearance. I would say this happens on about one out of 20 engines, but we really try to keep our tolerances in the middle zone. If you encounter this, we have 1 thousandths under bearings, and you should use them if needed, as this is important for engine longevity.
Don't confuse what we are saying with a turned crank. Those cranks are smaller by 10 thousandths or more. It's not uncommon for many GM stock cranks to have 1 under or over bearings in them right out of the factory. We rarely run into this, but don't assume anything. Just check before installing, and let us know if you need a set of 1 under or over bearings or the half shells.
Our choice of rods are the Genuine Scat brand heavy duty 6.135 H-Beam rods with ARP cap screws
KING MAIN AND ROD BEARINGS ARE INCLUDED.
WISECO FULLY FORGED PISTONS RATED AT 800+ HP. THESE PISTONS ARE VERY RESISTANT TO THE DAMAGE CAUSED BY DETONATION COMPARED TO NON FORGED OR HYPEREUTECTIC PISTONS. WISECO PISTONS ARE 100% MANUFACTURED IN THE USA. THEY ARE ONE OF THE HIGHEST RATED PISTON BUILDERS IN THE COUNTRY.
Our custom made Wiseco forged pistons are made from 2618 aircraft alloy, and are capable of handling far more hp than a cast or hypereutectic piston. We find this alloy to be much more suitable for high performance engines than the common 4032 forged alloy that many others offer. You will usually see the higher end pistons on the market using 2618 aircraft alloy.
Why go with 2618 forged pistons? If you encounter certain tuning issues, detonation is highly probable, and it can cause severe damage to your engine. The 2618 forged piston is able to withstand the effects from detonation to a higher degree than the lower cost 4032 forged pistons, especially non-forged hypereutectic pistons such as Speed Pro or Keith Black.
These pistons are also suitable for use with nitrous or blower setups, but for those not running forced induction, the forged pistons offer very high reliability. The 2618 forged piston is far stronger than hypereutectic pistons. For the slight increase in cost, this setup is the best value on the market.
We would not even consider using Speed Pro, Keith Black (KB), or any brand of hypereutectic pistons due to the possible fragmentation that could occur during detonation. If you're in doubt about this, do an internet search on the subject. Forged pistons are far superior to cast or hypereutectic pistons in many ways, especially our custom made Wiseco pistons made from 2618 aircraft alloy.
Having high quality forged pistons will be your only hope should the conditions arise for detonation to occur. We sell nothing but forged pistons, as I find it comforting to know that my customers will have an engine with a tremendous safeguard built into it. Support rails, wrist pins, and pin locks included.
All of our Wiseco forged pistons are custom made for us and will sit flush in the block at a deck height of 9.790. If you have a virgin block, the deck height is at 9.900 and most machine shops will shave approx. 5-10 thousandths to remove any warping and put down a fresh finish. This puts the block right at 9.790 or less, creating a zero deck with these pistons. Most other catalog pistons sit .025 below stock deck height. Their reasoning for this: should the block have been decked multiple times, then the pistons will not be sitting too far above the deck surface. It is rare that you will see a block end up at 9.775. If you have one that is at that height, it would be highly compromised, in our opinion. Should you decide to use a block with a deck height around 9.775, then you can use a thicker head gasket to compensate for this.
Important note.
This assembly is to be used in standard deck blocks that were originally 9.800". This is not to say the 9.800" block has to remain at this height, as cleaning up the surface may be required, and that will not pose a problem. Most industrial blocks used in large trucks and buses had deck heights of 10.200" and these will NOT work with this assembly. It would be fair to say that 100% of all car and pickup trucks used the 9.800" block and those are compatible, providing they can be bored to the correct size needed for this assembly. Aftermarket blocks such as Dart are not a problem as long as they are standard deck height.
A few more facts about our custom made
Wiseco pistons and deck height.
Leaving the deck thick on your block makes for a stronger block that resists flexing and also runs cooler as the deck has a lot to do with the dissipation of heat. Blocks with decks cut down this low are prone to cracking. Our pistons are designed to sit flush at 9.790 rather than at 9.775. Those using catalog pistons can't leave the deck as thick because it will allow the piston to sit too far down in the block, killing the quench/squish zone. All of our pistons sit flush at 9.790 to keep our customers from having to butcher the block in order to obtain a decent quench/squish zone.
Should your block have had a large amount of surface removed in the past, and if your pistons are around .005 out of the block, there are many .050 head gaskets on the market. We would like to see you maintain a quench/squish zone of approx. .040 So should your piston calculate to being .005 out of the block, an .050 gasket will give you a quench/squish zone of approx. .045
Because our pistons are at a taller than normal compression height, you will save money on having to deck the block only 10 thousandths or less rather than 25 thousandths as most other pistons require to obtain a zero deck height. It is also highly desirable to keep the deck as thick as possible.
Another good feature about our pistons having a taller compression height is that the ring land above the top ring is much stronger by being .015 thicker than most other pistons on the market. When pistons encounter the effects of severe detonation, it is not uncommon to see the ring land above the top ring broken off. The thicker ring land also makes a better heat sink.
If you are having your block decked, be sure to let the machine shop know that these pistons will sit flush at 9.790 deck height. The compression height of our pistons is also listed in the ad. If you have a block that has been decked several times in the past and will need it again and ends up at 9.775, it is our recommendation that you find another block.
We have had many customers claim to have not taken their original block to be decked at all. If the deck is not warped and has a decent finish, this is somewhat acceptable but not recommended. However, leaving the block at stock deck height and using our pistons would only put the piston in the hole by .010 thous. and that is not bad at all. It is best to clean up the deck surface with a simple .010 cut, and achieve zero deck ht.
Item Code |
|
Vendor Name |
Wiseco |
Product Type |
Race Series for street/strip use |
Product Model |
Custom built for SWP |
Engine Displacement (cu.in.) |
454 |
Engine Family |
CHEVROLET - Big Block V8 |
Material |
2618 Fully Forged Aluminum |
Base Bore (in) |
4.250+.060=4.310 |
Stroke (in) |
4.00 |
Rod Length (in) |
6.135 |
Compression Height (in) |
1.655 |
Top Type |
Flat top |
Net Head Volume (cc) |
+3cc |
Deck Thickness (in) |
0.350 |
Weight Without Pin (g) |
498 |
Wrist Pin Diameter (in) |
STD |
Wrist Pin Length (in) |
|
Wrist Pin Weight (g) |
157 |
Pin Lock Type |
Spiral |
Ring Set # |
683-30 |
Top Ring Groove Size |
5/64 in. |
Second Ring Groove Size |
5/64 in. |
Oil Ring Groove Size |
3/16 in. |
Top Ring Land (in) |
|
Second Ring Land (in) |
|
Bottom Ring Land (in) |
|
Quantity |
8. |
HASTINGS 2M SERIES MOLY RINGS
We offer premium grade Ram brand SFI Billet Steel flywheels for manual transmission use at an additional cost. See our other listings. This assembly includes a flexplate for automatic transmission use at no additional cost.
When choosing a flywheel for manual transmission use, be sure to know what tooth count you need. There are two sizes available, and it is of the utmost importance to select the flywheel that is correct for this assembly. There are several factors that must be addressed when choosing your correct flywheel. The tooth count must be correct. This is very important. There are two sizes available, and it is the bellhousing size on the transmission that determines this. Another important factor is if the assembly your purchasing is internally balanced often referred to as neutral balanced or if it is an externally balanced assembly, often referred to as externally balanced. All of our assembly ads will have this information in them. Big block and small block engines will also have a different bolt pattern in most cases. To sum it up, there are three important factors to look for when selecting the correct flywheel, tooth count, int. or ext bal. and whether or not you have a big block or small block engine. The Ram brand flywheels we offer are very high quality.
We have noticed others using a low grade knockoff brand damper/balancer, and we have encountered them in the past. They are substandard in appearance, and are often out of spec. The timing marks were also poorly marked on some of the balancers we have come across. You don't want a balancer coming off or one that is improperly weighted. Another problem with low grade dampers is the elastomer bonding can lose its adherence to the inner and outer structure. This problem is referred to as a slipped damper. We have only encountered this once in 10 years with the Pro-Race brand dampers.
We know of several competitors including these balancers with rotating assemblies. The Pro-Sport SFI is far superior to most any we have ever seen. They were once known as a knockoff product, and have become one the best values on the market, without comprising quality whatsoever.
Rust warning.
If you are going to store your rotating assembly or short block kit for any length of time, it is very important that you protect these parts by spraying a light coat of rust preventive substance on all bare metal parts. This is especially important for those storing these parts in a high moisture or humid environment. Very light surface rust is easily removable and will cause no harm, but heavy rust can damage these parts and be very costly to fix.
We offer this assembly with selected upgrades. Listed below are some of the most requested ones. Many not only improve performance, but further enhance the reliability and longevity of your engine, along with resale value.
SFI Certified Flexplate: This is a very low cost upgrade and may be required when racing your car at certain tracks. The flexplate that comes with this assembly is a heavy duty plate, but the SFI certified plate is one step up in quality and safety. This SFI plate is made in North America. We noticed these have much less run-out and warpage than we see with many other plates on the market. Plates with too much run-out and warpage can cause a host of problems for your transmission and starter, and affect balancing. The low cost to upgrade to this is well worth, it in our opinion.
Cost of this upgrade is $24.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart.
On occasion we are unable to obtain the Pioneer brand SFI flexplate and will substitute it for the Scat SFI brand plate pictured below. The quality is equal in every aspect.
Crank polishing: Extends bearing life, reduces oil temp, frees up a slight amount of average horsepower. This is a very low cost upgrade, and in the world of mass production, most cranks do not come with a true polished finish. This is why most machine shops have a machine to do this. The difference is dramatic between a crank right out of the box and one that we have polished. Bearing companies claim that cranks that have better finishes on the journals will survive the break-in better, and have much longer bearing life. We do a two-step process and bring the RA numbers down in the single digit range. We have the most advanced crank polishing machine on the market.
Clevite Bearings: We find the Clevite bearings to be a somewhat better product overall. Clevite is what we now use in all of our engines. This is not to say that King bearings are faulty in any way, but under certain conditions, we have seen fewer problems develop with Clevite bearings during break-in. We have sold King bearings for many years and do not hear of problems from our customers, but our experience on the dyno has shown the Clevite bearings have a better surface appearance upon tear-down after many dyno passes.
Rod sizing: All new rods, regardless of brand, must be checked for sizing on a Sunnen machine, and corrected if needed. You will seldom see a complete set of rods that have perfect sizing on both ends right out of the box. This upgrade is a must for those building their engine without the services of a machine shop.
Race balancing: This is for those who want the engine to operate virtually vibration free at high rpm. Extends engine life and frees up a few more horse power. This is a somewhat labor intensive procedure and is not required, but the feel of an absolutely vibration free engine at high rpm is desirable by many. The standard balance job that is included with this assembly at no extra charge is certainly sufficient. With a race balance job, all pistons and rods are match weighed to within 2/10's of a gram or less, and the final balance is brought down to around 1 gram plus or minus. An ultra smooth engine at high rpm has a noticeable feel and sound to it. If you do not opt for this upgrade, the assembly will still be fully balanced. We spend a good hour and a half doing the regular balance work, and it will certainly meet your needs.
ARP-2000 rod bolts: This is one upgrade that we find to be very valuable. The rod bolts are most likely to fail under hard use, more so than the rod itself. When a rod bolt fails during high RPM, total engine destruction is usually the result. The ARP-2000 rod bolts are a very good upgrade, in our opinion. We actually have few, if any, problems with the regular ARP-8740 bolts, but those who run hard always upgrade to the ARP-2000 rod bolts. The ARP-2000 rod bolts also torque at a higher number, and this increased clamping force is also a factor in keeping the big end of the rod stable and true to size. The ARP-2000 bolts are installed in the rods and this upgrade is only available with the Competition rod upgrade. Cost is $89.50
Scat or Eagle 4340 Forged Crank: The forged Scat crank has a rating of 800+ HP. This is the ultimate upgrade for those wanting to run hard. Nos, blowers, turbos, are not an issue with this crank. Even without such power adders, this Crank offers great protection under the most severe conditions. This upgrade also comes with the high Performance King bearings. Should you decide to run power adders in the future, this would be essential. The fatigue life of the 4340 crank over the cast nodular is also greatly extended. We do offer this upgrade as part of many of our assemblies in our other listings. They have the key words, "fully forged," in the title.
The upgrades above are all available in our other listings. Some of these are often requested by those building an engine without a machine shop. We find most of these upgrades very valuable for those wanting to take longevity and durability to the next level. They are all bottom end related, and that's an area worth investing a few more dollars into, in our opinion, especially if you're planning on running long and/or hard. These upgrades are also valuable for your build history on your engine, and would certainly increase the resale value of your engine, should you ever sell it.
A note from Skip White, company president.
We have built this setup for many people that are into serious street/strip use as well as drag racing, and have yet to experience a failure. Every part in this assembly meets our satisfaction. I can promise you that many assemblies offered by other sellers pale in comparison to ours. This is the best value you will find on the market.
Many people have asked how is it that we can sell this assembly for such a low price. To answer this; we buy our products at master WD (warehouse distributor) level for all of the items in this assembly, and we are selling direct to the public. We are a volume sales based company. Our profit is based on sheer volume, with a very low markup. By selling large volumes, we have to purchase large volumes of products. It is this large volume purchasing that allows us to buy products at a much lower price and we simply pass these savings on to our customers.
Skip White
|
Customer Reviews
This product does not have any reviews yet.